Installation Instructions

Failure to follow instructions carefully may cause damage.

Katch is intended for temporary surface protection. Avoid adhering to surfaces where delamination is present as it may cause damage to the surface. Surfaces must be clean, dry, and free of any chemical cleaners and contaminants. Test the material in a small inconspicuous area to ensure adequate adhesion and clean removal without surface damage. Before introducing the product into any new location, especially ignitable materials, the user should conduct a proper industrial hygiene risk assessment. Doing so will help confirm the product is appropriate for its setting, application, safety, and removal.

Required surface preparation:

Sweep or vacuum surfaces to remove loose dirt and dust.
Surfaces must be thoroughly dry for proper adhesion.
Surfaces must be free of all chemical cleaners and residue.
Check the surface for damage or delamination before applying the material.

Recommended application:

Avoid stretching material during installation.
Avoid significant overlaps (more than 1").
Smooth material down using hand or a flat edge squeegee.
Cut to length with scissors or a razor blade from the non-adhesive side.

How to use:

Roll out Katch and attach to the surface with the adhesive side down.
Should be attached starting at one end and attaching as the product lays down from end-to-end.
Smooth to reduce bubbles and wrinkles using hand or a flat edge squeegee.
It is recommended not to lay straight down, as it will create extra and unnecessary wrinkles.
To reuse, pull up the same direction it was applied. Start at one end, lift, and re-attach using installation instructions, laying it down from end-to-end. Smooth out any wrinkles.

Spill protection:

Product construction is designed to be impervious to many liquids including standard water-borne or solvent-borne products (paints, cleaners, etc.) and oils.
To ensure safety, it is recommended to clean up spills that pool on the surface of the product after the spill occurs.
Product can continue to be used after the spill has been cleaned up.

Removal:

Make sure all liquid combustible-type products have been removed or have evaporated.
Manually pull up the product in the same direction that it was applied.
Vacuum up any loose debris if necessary.
Reapply product to the work surface(s) following the "Installation Instructions."
Reuse as long as the temporary adhesive on Katch is still functional. Usually, it will last 3-5 times being re-attached, but performance will vary depending on use and surface.

Change out recommendation:

For most applications, the general guideline would be 2-4 weeks.
To ensure clean and easy removal, the material replacement schedule should be based on the type of surface, amount of liquid, and the weight and frequency of the traffic going over the product.

Disposal:

Consult local and state guidelines for proper disposal

Flammability:

Class 1 Interior Floor Finish
Class 1 (A) Interior Wall Finish

The plastic bag/film is dangerous as a choking hazard. Keep away from children.

Static Discharge

Katch is a strippable covering intended to help protect and facilitate the cleaning of work surfaces. Do not apply or remove the product when explosive concentrations of ignitable materials are present, as static discharge may occur during such activity. Before application and removal, users are instructed to provide mechanical ventilation to disperse or exhaust ignitable vapors and dust per good industrial hygiene practice.

Applications

Storage and Handling

For best performance, use this product within 24 months from the date of manufacture.
Store product in the original carton under normal conditions of 70F (21C) and 50% relative humidity.
Avoid storing material in temperatures above 85F (29C) for long periods.
Keep material covered and clean.

⚠ WARNING:

To reduce the risks associated with fire and explosion: Do not apply or remove the product when explosive concentrations of ignitable materials are present. Static discharge may occur during such activity. Provide mechanical ventilation to disperse or exhaust combustible vapors and dust per good industrial hygiene practice.

⚠ WARNING:

To reduce the risks associated with fire and explosion or tripping and falling: Pooled liquid on the product should be wiped up immediately.

⚠ CAUTION:

Ensure product edges are bonded firmly to flooring and/or walking surfaces to reduce the risks associated with tripping and falling.

Technical Information

The technical information, guidance, and other statements contained in this document or otherwise provided by 3M are based upon records, tests, or experience that 3M believes to be reliable, but the accuracy, completeness, and representative nature of such information is not guaranteed. Such information is intended for people with knowledge and technical skills sufficient to assess and apply their own informed judgment to the information. No license under any 3M or third-party intellectual property rights is granted or implied with this information.

Product Selection and Use

Many factors beyond 3M's control and uniquely within the user's knowledge and control can affect the use and performance of a 3M product in a particular application. As a result, the customer is solely responsible for evaluating the product and determining whether it is appropriate and suitable for the customer's application, including conducting a workplace hazard assessment and reviewing all applicable regulations and standards (e.g., OSHA, ANSI, etc.). Failure to properly evaluate, select, and use a 3M product and appropriate safety products, or to meet all applicable safety regulations, may result in injury, sickness, death, and/or harm to property.

Warranty, Limited Remedy and Disclaimer

Unless a different warranty is specifically stated on the applicable 3M product packaging or product literature (in which case such warranty governs), 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ARISING OUT OF A COURSE OF DEALING, CUSTOM, OR USAGE OF TRADE. If a 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price.

Limitation of Liability

Except for the limited remedy stated above, and except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from or related to the 3M product, whether direct, indirect, special, incidental, or consequential (including, but not limited to, lost profits or business opportunity), regardless of the legal or equitable theory asserted, including, but not limited to, warranty, contract, negligence, or strict liability.